木工加工棚搭建的目的是什么？木工加工棚是為了保護施工現場建筑材料，防止施工現場的物品被雨水淋濕而生銹，因此需要搭建加工棚進行保護，而且它的作用和特點特別的鮮明。

What is the purpose of the woodworking shed? The carpentry processing shed is designed to protect the building materials on the construction site and prevent the articles on the construction site from being wet by rain and rusting. Therefore, it is necessary to build a processing shed for protection, and its function and characteristics are particularly clear.

加工棚是為了保護施工現場的施工人員，用鋼管作為支撐框架，用竹簽或竹笆板或廢棄模板覆蓋作為防砸，或保護高壓線等穿過加工棚的東西。一般雙層保護是為了增加系數。

The processing shed is designed to protect the construction personnel on the construction site. The steel pipe is used as the support frame, and the bamboo stick or bamboo fence board or waste formwork is used as the anti smashing, or the high-voltage line and other things passing through the processing shed are protected. The general double-layer protection is to increase the safety factor.

加工棚是建筑施工過程中操作人員或人行的必經通道，過往人員的加工棚為雙層。從懸挑腳手架的懸挑處開始，每隔十米設置一個加工棚，可以更好地保證加工棚下行走人員的。

The processing shed is a necessary passage for operators or pedestrians during the construction process. The processing shed for passing personnel is double-layer. Starting from the cantilevered part of the cantilevered scaffold, a processing shed is set every ten meters to better ensure the safety of the walking personnel under the processing shed.

在施工過程中，在搭建加工棚時注意防護措施，施工人員按照施工要求進行施工，露天攪拌機位置、現場混凝土攪拌機、卷揚機棚、鋼筋棚、木棚、部分出入口和現場廁所需要設置木工加工棚。

During the construction process, pay attention to the protective measures when building the processing shed. The construction personnel shall carry out the construction according to the construction requirements. The woodworking processing shed shall be set at the outdoor mixer position, the site concrete mixer, the winch shed, the reinforcement shed, the wooden shed, some entrances and exits and the site toilet.

水平保護安裝和拆除前，進行技術交底。安裝和拆除水平加工棚時，操作人員的“三寶”齊全并正確使用。加工棚搭設和拆除時，應避免上下同時作業，錯開作業時間。

Safety technical disclosure shall be conducted before installation and removal of horizontal protection. When installing and removing the horizontal processing shed, the "three safety treasures" of the operators shall be complete and correctly used. During the erection and dismantling of the processing shed, the simultaneous operation of the upper and lower parts shall be avoided and the operation time shall be staggered.

安裝和拆除加工棚時，所有材料和工具應堆放在建筑物外緣少2m處，堆放高度不得超過1m。拆除的材料及時傳遞到地面并運走，嚴禁高空拋擲。建造和拆除加工棚時，應在地面上設置警戒區，并派專人監控。

When installing and removing the processing shed, all materials and tools shall be stacked at least 2m away from the outer edge of the building, and the stacking height shall not exceed 1m. The demolished materials shall be delivered to the ground and transported away in time. Throwing from height is strictly prohibited. During the construction and removal of the processing shed, a warning area shall be set on the ground and a special person shall be assigned to monitor.

建造和拆除加工棚時，應指定專人指揮。管理人員應注意眼、腿、口，采取有效的防護措施應對危險情況，確保人員。在雨天和大風天氣，應暫停加工棚的搭設和拆除，并檢查和維護加工棚的質量。

During the construction and removal of the processing shed, a special person shall be appointed to command. The management personnel shall pay attention to the eyes, legs and mouth, take effective safety protection measures to deal with dangerous situations and ensure personnel safety. In rainy and windy days, the erection and removal of the processing shed shall be suspended, and the quality of the processing shed shall be inspected and maintained.

加工棚搭設完成后，經專職員驗收合格后方可投入使用。在搭設和拆除水平防護前，進行技術交底。

After the erection of the processing shed is completed, it can be put into use after passing the acceptance of the full-time safety officer. Safety technical disclosure shall be conducted before setting up and removing horizontal protection.

加工棚是建筑施工過程中操作人員或人行的必經通道，過往人員的加工棚為雙層。從懸挑腳手架的懸挑處開始，每隔十米設置一個懸挑式加工棚，可以更好地保證加工棚下行走人員的。更多相關事項就來我們網站http://m.litoele.com進行咨詢吧。

The processing shed is a necessary passage for operators or pedestrians during the construction process. The processing shed for passing personnel is double-layer. Starting from the cantilevered part of the cantilevered scaffold, a cantilevered processing shed is set every ten meters to better ensure the safety of the walking personnel under the processing shed. For more information, please visit our website http://m.litoele.com Let's consult.